Looking for Help?

Find answers to your questions

B, [Wireless Settings] Wireless General Settings

Table of Contents

  1. Wireless Barcode Scanner General Settings
    1. 1、Get Firmware Version
    2. 2、Factory Reset
    3. 3、Operating Mode
    4. 4、Power Management
    5. 5、RTC Clock Settings
    6. 6、Scan Modes
    7. 7、Decode Time
    8. 8、Information Prompt

Wireless Barcode Scanner General Settings

 

1、Get Firmware Version

Get Version Number

 

 

2、Factory Reset

Restore Factory Settings

 

 

Write to Custom Defaults

 

 

Restore Custom Defaults

 

 

3、Operating Mode

Normal Mode

 

 

 

Store Mode

 

Memory Data Upload

 

 

 

Get Memory Barcode Number (Total Count)

 

 

 

Clear Memory After Upload

 

 

 

Check Memory Usage

 

 

 

Clear Memory Barcodes

 

 

 

Auto Store Mode Off

 

 

 

 

Auto Store Mode On

 

 

 

NOTE 1: During data upload, scanning "Memory Data Upload" again will cancel/stop the upload.

NOTE 2: In wireless transmission mode, if auto store mode is enabled and a wireless 2.4G transmission fails, the barcode will be automatically stored and can be retrieved by scanning "Memory Data Upload."

 

 

4、Power Management

① Sleep Time Read

Read Sleep Time

 

② Set Sleep Time

  • Power Off: Immediate Sleep
  • Sleep Time = 1 min
  • Sleep Time = 3 min
  • Sleep Time = 5 min
  • Sleep Time = 10 min
  • Sleep Time = 30 min
  • Sleep Time = 1 hour
  • Sleep Time = 2 hours
  • Never Sleep

 

 

③ Get Scanner Battery Level

Get Battery Rough Level

 

 

5、RTC Clock Settings

  • NOTE: Applicable only to scanners that support RTC.

  • Set the time by scanning the following format: “yy/mm/dd, hh:mm

    ” (includes time zone, so the local time is displayed). Example: %RTCTIME#23/05/26,16:21:40. Alternatively, synchronize time via Bluetooth SDK.

Disable Time Stamp*

 

 

Enable Time Stamp

6、Scan Modes

Barcode Decoder Scan Mode*

Key Scan Mode (Default)

 

 

Continuous Scan Mode

 

 

Note: Continuous scan mode is ideal for rapid scanning, such as in a courier scenario. Trigger the scan by pressing the Trigger button to start or stop scanning.

Key Pulse Scan Mode

 

Note: Scanning begins when a button press is detected (maintained for approximately 30ms) and ends when another button press is detected. Scanning stops upon successful decoding or timeout.

Host Trigger Mode

 

 

7、Decode Time

①Decode Timeout

  • This parameter sets the maximum time for decoding attempts during scanning. Default: 3000ms, Range: 0500-9999ms.

3s (Default)

 

 

6s

 

 

②Decode Interval

  • Interval time between scans in Continuous Mode. Default: 500ms, Range: 0100-9999ms.

0.5s (Default)

 

 

1s

 

 

8、Information Prompt

① Beep Control

Mute

 

 

High Volume

 

 

Medium Volume

 

 

Low Volume

 

 

High Tone

 

 

Low Tone

 

 

SDK Sound Response Off

 

 

SDK Sound Response On

 

 

Base Connect Beep Prompt On/Off

Note: Not all barcode scanners have the "Base Connect Beep Prompt" or "SDK" function.

 

 

② Vibration Control

Disable

 

 

Enable

Note: The vibration motor works when the beep sounds. Not all barcode scanners have this function.

 

 

③Sound Prompt

Type Beep Sound Meaning Description
Prompt tone 1 beep 2 tones Store mode scan data, Power off sound.
1 beep 3 tones Power on sound, setting success, Upload finish prompt 
1 Short beep One short sound for successful barcode scan. 
Continuous beeps (30s): RF pairing mode waiting for dongle insertion, stops upon successful pairing.
     
Warning tone Two beeps Battery low warning during scanning.
Three beeps Error saving barcode in store mode or exceeding memory capacity,
Transmit failed beeps. 
Five beeps Power on failed due to low battery.

 

④LED Indicators

LED State
RED，GREEN Charging: Red on, Green off; Charge complete: Red off, Green on.
BLUE Blue LED follows speaker; in Bluetooth mode (if supported), it indicates the Bluetooth connection status.

 


C750 General Settings Wireless Settings

Updated on 22 Aug 2024